Difference between revisions of "Remote Control"

From Silent Wings Wiki
Jump to: navigation, search
(Protocol)
 
(2 intermediate revisions by 2 users not shown)
Line 42: Line 42:
 
  FLP <value>              - Flaps, [ 0.0 - 1.0 ]
 
  FLP <value>              - Flaps, [ 0.0 - 1.0 ]
 
  RUD <value>              - Rudder, [ -1.0 - 1.0 ]
 
  RUD <value>              - Rudder, [ -1.0 - 1.0 ]
 +
TRM <value>              - Elevator trim, [ -1.0 - 1.0 ]
 +
GEAR <value>              - Gear [0,1]
 +
WTR <value>              - Water valves (int)
 
  THR <value>              - Throttle, [ 0.0 - 1.0 ]
 
  THR <value>              - Throttle, [ 0.0 - 1.0 ]
 
  PIT <value>              - Propeller pitch, [ 0.0 - 1.0 ]
 
  PIT <value>              - Propeller pitch, [ 0.0 - 1.0 ]
Line 47: Line 50:
 
  PBK <value>              - Parking brakes [ 0, 1 ]
 
  PBK <value>              - Parking brakes [ 0, 1 ]
 
  PRBK <value>              - Propeller brake [ 0.0 - 1.0 ]
 
  PRBK <value>              - Propeller brake [ 0.0 - 1.0 ]
 +
IGN <value>              - Ignition, [0,1]
 
  MIX <value>              - Mixture, [ 0.0 - 1.0 ]
 
  MIX <value>              - Mixture, [ 0.0 - 1.0 ]
  TRM <value>              - Elevator trim, [ -1.0 - 1.0 ]
+
  MAG <value>              - Magnetos, [1,2,3]
 +
FUV <value>              - Fuel valve
 +
FUT <value>              - Fuel tanks
 +
FUP <value>              - Fuel pump, [0.1]
 
  ENST <value>              - Engine start [ 0, 1 ]
 
  ENST <value>              - Engine start [ 0, 1 ]
 
  DCMP <value>              - Engine decompression [ 0, 1 ]
 
  DCMP <value>              - Engine decompression [ 0, 1 ]
 
  PRM <value>              - Fuel primer, [ 0, 1 ]
 
  PRM <value>              - Fuel primer, [ 0, 1 ]
 +
CHT <value>              - Carburetor heat, [0.0 - 1.0]
 +
CWFP <value>              - Cowling flap [0.0 - 1.0]
 
  EEXT <value>              - Engine boom extend, [ 0, 1 ]
 
  EEXT <value>              - Engine boom extend, [ 0, 1 ]
 
  ERET <value>              - Engine boom retract, [ 0, 1 ]
 
  ERET <value>              - Engine boom retract, [ 0, 1 ]
Line 63: Line 72:
 
  APRUD <enable>            - Auto pilot, auto rudder enable/disable, [0, 1] (Coordinated flight).
 
  APRUD <enable>            - Auto pilot, auto rudder enable/disable, [0, 1] (Coordinated flight).
 
  APSPDC <enable>          - Auto pilot, speed command enable/disable, [0, 1].
 
  APSPDC <enable>          - Auto pilot, speed command enable/disable, [0, 1].
  HUD <enable>             - Enable/disable HUD, [ 0, 1 ].
+
  HUD <mode>               - Set HUD: 0 = Off, 1 = Flight mode, 2 = Competition mod.
 
  JOY <enable>              - Enable/disable Joystick control, [0,1].
 
  JOY <enable>              - Enable/disable Joystick control, [0,1].
 
  VIEW <mode>              - Set view mode: 0 = Cockpit, 1 = Spot, 2 = Fixed, 3 = Flyby, 4 = Free flight, 5 = Chase, 6 = Overview
 
  VIEW <mode>              - Set view mode: 0 = Cockpit, 1 = Spot, 2 = Fixed, 3 = Flyby, 4 = Free flight, 5 = Chase, 6 = Overview
Line 81: Line 90:
 
  FLT                      - Switch to flight screen
 
  FLT                      - Switch to flight screen
 
  HELP <enable>            - Enable/disable help window, [0,1]
 
  HELP <enable>            - Enable/disable help window, [0,1]
 +
PLB <enable>              - Enable/disable playback controls (Viewer only)
 +
RSLT <enable>            - Enable/disable results window [0,1]
 +
SPLT <enable>            - Enable/disable standings plot window [0,1]
 +
AC <number>              - Set current aircraft [1, n]
 +
OFS <seconds>            - Offset current time by <seconds> (Viewer only).
 +
  
 
[[Category:Interfaces]]
 
[[Category:Interfaces]]

Latest revision as of 22:25, 26 August 2008

Note: This feature is implemented in Silent Wings 1.08. It will not work with earlier versions

Silent Wings contains a built-in server which can be used to control most functions of the simulator. This can be used from external applications to interface certain types of hardware, custom autopilot applications and probably a lot of other interesting uses.

To enable the Remote Control server, add the following lines to options.dat


use_remote_control = true
remote_control_port = 6070
remote_control_mode = UDP

The last variable can be either UDP or TCP.

To test it, set mode to TCP and telnet to the correct port on the computer running Silent Wings, for example:

telnet localhost 6070

You can now enter commands directly in the telnet window, for example:

HELP 0
PAUSE 0
APSPD 1 100
APROL 1 30
VIEW 3

This will close the help window, unpause and put the aircraft in a 30 degrees bank at 100km/h using the autopilot. Finally, it will change view to flyby-mode.

To test with UDP, you need to use the command:

nc -u localhost 6070

The Netcat (nc) command is also available on Windows, although some virus checkers regard it as a "hacker tool". Do a google search.

Protocol

The following commands are recognized by the server

AIL <value>               - Ailerons, [ -1.0 -1.0 ]
ELE <value>               - Elevator, [ -1.0 -1.0 ]
ABK <value>               - Airbrakes, [ 0.0 - 1.0 ]
FLP <value>               - Flaps, [ 0.0 - 1.0 ]
RUD <value>               - Rudder, [ -1.0 - 1.0 ]
TRM <value>               - Elevator trim, [ -1.0 - 1.0 ]
GEAR <value>              - Gear [0,1]
WTR <value>               - Water valves (int)
THR <value>               - Throttle, [ 0.0 - 1.0 ]
PIT <value>               - Propeller pitch, [ 0.0 - 1.0 ]
WBK <value>               - Wheel brakes, [ 0.0 - 1.0 ]
PBK <value>               - Parking brakes [ 0, 1 ]
PRBK <value>              - Propeller brake [ 0.0 - 1.0 ]
IGN <value>               - Ignition, [0,1]
MIX <value>               - Mixture, [ 0.0 - 1.0 ]
MAG <value>               - Magnetos, [1,2,3]
FUV <value>               - Fuel valve
FUT <value>               - Fuel tanks
FUP <value>               - Fuel pump, [0.1]
ENST <value>              - Engine start [ 0, 1 ]
DCMP <value>              - Engine decompression [ 0, 1 ]
PRM <value>               - Fuel primer, [ 0, 1 ]
CHT <value>               - Carburetor heat, [0.0 - 1.0]
CWFP <value>              - Cowling flap [0.0 - 1.0]
EEXT <value>              - Engine boom extend, [ 0, 1 ]
ERET <value>              - Engine boom retract, [ 0, 1 ]
TBO <value>               - Engine turbo, [ 0.0 - 1.0 ]
PANH <value>              - Camera pan horizontal (degrees)
PANV <value>              - Camera pan vertical (degrees)
ZOOM <value>              - Zoom +/-
APHDG <enable> <target>   - Auto pilot, heading hold. Enable/disable with 1/0, target in degrees.
APSPD <enable> <target>   - Auto pilot, speed hold. Enable/disable with 1/0, target in km/h.
APROL <enable> <target>   - Auto pilot, auto bank. Enable/disable with 1/0, target in degrees. 
APRUD <enable>            - Auto pilot, auto rudder enable/disable, [0, 1] (Coordinated flight).
APSPDC <enable>           - Auto pilot, speed command enable/disable, [0, 1].
HUD <mode>                - Set HUD: 0 = Off, 1 = Flight mode, 2 = Competition mod.
JOY <enable>              - Enable/disable Joystick control, [0,1].
VIEW <mode>               - Set view mode: 0 = Cockpit, 1 = Spot, 2 = Fixed, 3 = Flyby, 4 = Free flight, 5 = Chase, 6 = Overview
SRT <val>                 - Simulation rate: < 0.0 - 64.0 ]
QUIT                      - Quit simulation
RST                       - Restart simulation
PAUSE <enable>            - Enable/disable pause
CPT <enable>              - Enable/disable cockpit graphics, [0,1]
TRK <enable>              - Enable/disable track ribbons, [0.1]
LAB <enable>              - Enable/disable labels, [0,1]
PIC                       - Grab screenshot
TSK <enable>              - Enable/disable task graphics, [0,1]
THM <enable>              - Enable/disable thermal visuals, [0,1]
VEC <enable>              - Enable/disable force vectors, [0,1]
CHAT <message>            - Send chat message        
MAP                       - Switch to map screen
FLT                       - Switch to flight screen
HELP <enable>             - Enable/disable help window, [0,1]
PLB <enable>              - Enable/disable playback controls (Viewer only)
RSLT <enable>             - Enable/disable results window [0,1]
SPLT <enable>             - Enable/disable standings plot window [0,1]
AC <number>               - Set current aircraft [1, n]
OFS <seconds>             - Offset current time by <seconds> (Viewer only).